Sika  Waterbars  are  constructed  from  flexible  thermoplastic  PVC.  They are designed to stop the migration of water through construction joints in concrete  structures.

Sika  Waterbars  conform  to  the  performance  requirements  of  the  follow- ing  International  Standards  and  Specifications:  U.S.  Corps  of  Engineers

Specification  CRD-C  572-74,  BS  2782  and  BS2571, ASTM  D412/D624/ D746 and DIN 18541 Part 2.

Uses:

For the effective sealing of concrete construction joints in structures such as:

Water  reservoirs

Sewage  treatment  plants

Swimming  pools

Basements

Retaining  walls

Lift  shafts

Tunnels,  culverts

Service  pits

Advantages:

Sealing  starts  as  soon  as  the  concrete  has  hardened

Multi  rib  profile  provides  impenetrable  barriers  to  water  migration

Can  be  easily  site  welded  -  (welding  knife  is  available)

Factory  welded  junctions  are  available  on  request

Good  chemical  resistance

Available  various  kind  of  profiles  for  construction  joints

Product Da ta

Flexible Strip / Grey

15,  30  m  rolls

Dry,  shaded  place  (protected  from  sunlight)

Technical  Data

Polyvinyl Chloride

~ 1.30  kg/ltr

~70 ± 5 (DIN ~ 53505)

³12.17 N/mm  2 (ASTM - D412-75)

>300 % (ASTM D412-98a & DIN 18541 Part 2)

Approx. 200ºC

o                         o

-35 C to +55 C

Complies to CRD-C572-65 Army Corps of Engineers

Permanent: Seawater, sewage, acids (up to 10% conc.)

Temporary: Diluted inorganic alkalis, mineral acids, mineral oils and fuels

A2-part(split)formworkmaybeused  (preferred).  In this method, allow one half of the Watebar to jut out while

the  other  half  will  be  casted.   This Waterbar  is  clamped  between  the formwork.

Applications:

Fixing to slab

Place the Waterbar flat on the lean concrete  or  base  of  the  structure.

The formwork for the stopends will terminate  in  the  middle  of  the

Waterbar,  allowing  one  half  of  the

Waterbar  to  be  casted  while  the  other half be exposed to receive the  next casting.

The Waterbar performs its function  only  if  both  sides  are  well  embed- ded  in  the  concrete.  Avoid  forma- tion  of  honeycombs  by  vibrating carefully.

The consistency of the concrete it- self  should  be  neither  too  plastic nor  too  stiff,  and  the  aggregate must  be  well  graded.

Placing of fresh concrete near the Sika-Waterbar requires care, as other- wise  it  will  be  forced  from  its  position  by  the pressure  of  the  fresh  con- crete, i.e. the ends will fold up.   To prevent this, the same concrete pres- sure  must  be  present  on  both  sides  of  the  Waterbar.

Removal of formwork in the neighborhood of Sika-Waterbar must be done with care.

The end of the Waterbar should be thoroughly checked for honeycomb- ing  on  the  stop-end  and  repaired  if  necessary.   It  must  also  be  cleaned of  all  hardened  concrete  remnants  adhering  from  the  first  concrete stage.   Further  procedure  is  similar  to  the  first  stage.

On  site  welding  can  be  undertaken  using  a  Sika  Electric  Welding  Knife.

Both  ends  of  the  joint  are  heated  simultaneously  on  the  faces  of  the welding  knife  until  an  even,  molten  bead  of  PVC  appears.   The  welding knife  is  withdrawn  and  the  Waterbars  are  immediately  pushed  together.

The  joint  should  be  held  rigid  until  the  plastic  cools  down  and  solidifies.

Check  for  any  gaps  or  imperfect  joints.  Redo  the  welding  if  necessary.

Failures  can  be  caused  by  irregularities  of  cut  edges,  insufficient  heat, dust etc.